high ? , low esr, low esl - ?ld?series (npo) description this capacitor is made with a low loss npo dielectric constant and is built with a special multilayer structure (electrode design) providing the user with the best compromise between dimensions and electrical characteristics. the fact that its length is shorter than its width provides a lower inductance and a higher resonance frequency than an equivalent square sized capacitor. in addition, the contact surface of the metallization with the air being larger than standard allows a better thermal exchange when capacitor is dissipating heat. those parts will be delivered on tape under request. applications featuring low esr and low esl, those parts are mainly intended for applications in hf where low losses are required, meeting all basic requirements that a good capacitor has to display over a wide range of temperature and frequency. consequently, they will be used in tuning, bypassing, coupling, decoupling, impedance matching, d-c blocking (etc.) applications, everywhere in rf power ampli?rs, ?ters, oscillators etc. capacitance range 0.5 to 100 pf ( s ee table next page ) tolerance on capacitance below 10 pf: above and including 10 pf: b= 0.1 pf g= ? % c= 0.25 pf j= ? % d= 0.5 pf k= 10 % m= ?0 % rated voltage: proof voltage: 500 vdc 2.5 x ur for 5seconds operating temperature range -55 c to +175 c temperature coefficient of the capacitance 0 60 ppm /? insulation resistance (ri): 10 6 m ? @ 25 c & ur 10 5 m ? @ 125 c & ur all electrical, mechanical and environmental tests will comply and will be carried out in accordance with the european cecc 30000 & cecc32101-007 speci?ations. rf & microwave capacitors multilayer ceramic ?orcelain?- cld series (npo) 7-18 vol. 1 sales offices: visit our web site at http://www.temex.net preliminary
rf & microwave capacitors multilayer ceramic ?orcelain?- cld series (npo) 7-19 vol. 1 sales offices: visit our web site at http://www.temex.net dimensions (mm) terminations standard: tin-plated nickel (v) non magnetic: silver-palladium-platinum (a) resonance frequency see curves page 7 -20 . q factor see curves page 7 -20 . esr see curves page 7 -20 . admissible rms current please, consult us. how to order? 501 cld xxx (1) (2) (3) (4) xxx: 3 digits capacitance value (see table) (1): tolerance code (see table) (2): termination code (v or a) (3): marking l= if required (4): taping e = if required taping when requested, parts will be delivered taped and reeled as per iec 286: ?plastic embossed styrene 8 mm width on reel 180 mm (7 ?. ?unless otherwise prescribed: 1000 parts per tape. length (l) 1.8 0.3 mm width (w) 2.65 0.25 thickness (t) 2.30 max cr (pf) code tol. 0.5 0r5 (b), c, d 0.6 0r6 = 0.7 0r7 = 0.8 0r8 = 0.9 0r9 = 1.0 1r0 = 1.1 1r1 = 1.2 1r2 = 1.3 1r3 = 1.4 1r4 = 1.5 1r5 = 1.6 1r6 = 1.7 1r7 = 1.8 1r8 = 1.9 1r9 = 2.0 2r0 = 2.1 2r1 = 2.2 2r2 = 2.4 2r4 = 2.7 2r7 = 3.0 3r0 = 3.3 3r3 = 3.6 3r6 = 3.9 3r9 = 4.3 4r3 = 4.7 4r7 = 5.1 5r1 = 5.6 5r6 j, k, m 6.2 6r2 = 6.8 6r8 = 7.5 7r5 = 8.2 8r2 = 9.1 9r1 = 10 100 (g), j, k, m 11 110 = 12 120 = 13 130 = 15 150 = 16 160 = 18 180 = 20 200 = 22 220 = 24 240 = 27 270 = 30 300 = 33 330 = 36 360 = 39 390 = 43 430 = 47 470 = 51 510 = 56 560 = 62 620 = 68 680 = 75 750 = 82 820 = 100 101 =
rf & microwave capacitors multilayer ceramic ?orcelain?- cld series (npo) 7-20 vol. 1 sales offices: visit our web site at http://www.temex.net
|
